| SIMATIC Compact Field Unit PA Edition with 16x I/O channels PROFINET interface V2.3 (RT) Use of PROFINET bus adapter Media redundancy (MRP) PROFINET system redundancy (S2) Configuration in Run (CiR) Process interfaces: 8x PROFIBUS PA and 8x freely configurable DIQ Installation up to hazardous zone 2 Temperature range -40 to +70 °C Conformal coating Mounting on 35 mm standard mounting rail |
| General information |
| Product type designation | Compact Field Unit |
| HW functional status | E01 |
| Firmware version | V1.0 |
| FW update possible | Yes |
| Vendor identification (VendorID) | 002AH |
| Device identifier (DeviceID) | 060DH |
| Number of channels | 16 |
| Product function |
| I&M data | Yes; I&M0 to I&M4 |
| The user can configure digital channels as input/output as required | Yes |
| Digital channels can be parameterized | Yes |
| Engineering with |
| STEP 7 TIA Portal configurable/integrated as of version | - / - |
| STEP 7 configurable/integrated as of version | From STEP 7 V5.6 HF1 and higher |
| PCS 7 configurable/integrated as of version | V9.0 |
| PROFIBUS as of GSD version/GSD revision | - / - |
| Installation type/mounting |
| Mounting | on 35 mm DIN rail, 2 spacing units wide |
| Mounting position | Horizontal, vertical |
| Supply voltage |
| Type of supply voltage | 24 V DC |
| Rated value (DC) | 24 V |
| permissible range, lower limit (DC) | 19.2 V |
| permissible range, upper limit (DC) | 28.8 V |
| Reverse polarity protection | Yes |
| Short-circuit protection | Yes |
| Redundant power supply | Yes |
| Mains buffering |
| Mains/voltage failure stored energy time | 5 ms; Bridging for field devices and communication |
| Input current |
| Current consumption (rated value) | 2.5 A |
| Current consumption, max. | 2.55 A |
| Inrush current, max. | 8 A |
| I²t | 0.3 A²·s |
| Encoder supply |
| Number of outputs | 8 |
| Output voltage encoder supply, min. | 18.2 V |
| Short-circuit protection | Yes; Electronic |
| Output current |
| up to 60 °C, max. | 2 A |
| up to 70 °C, max. | 1 A |
| Power loss |
| Power loss, typ. | 8.2 W; Depending on the type of BusAdapter used (typ. RJ45) |
| Address area |
| Address space per station |
| Address space per station, max. | 1 440 byte; Dependent on configuration |
| Digital inputs |
| Number of digital inputs | 8 |
| Source/sink input | Yes; P-reading |
| Input characteristic curve in accordance with IEC 61131, type 1 | Yes |
| Input characteristic curve in accordance with IEC 61131, type 2 | No |
| Input characteristic curve in accordance with IEC 61131, type 3 | Yes |
| Pulse extension | No |
| Number of simultaneously controllable inputs |
| horizontal installation |
| — up to 60 °C, max. | 8; Total current must be observed, see DQ |
| — up to 70 °C, max. | 8; Total current must be observed, see DQ |
| vertical installation |
| — up to 60 °C, max. | 8; Total current must be observed, see DQ |
| Input voltage |
| Rated value (DC) | 24 V |
| for signal "0" | -30 to +5V |
| for signal "1" | +11 to +30V |
| Input current |
| for signal "1", typ. | 2.5 mA; Typical |
| Input delay (for rated value of input voltage) |
| for standard inputs |
| — parameterizable | No |
| — at "0" to "1", max. | 3.2 ms |
| — at "1" to "0", max. | 3.2 ms |
| Cable length |
| shielded, max. | 1 000 m |
| unshielded, max. | 600 m |
| Digital outputs |
| Type of digital output | Transistor |
| Number of digital outputs | 8 |
| Current-sinking | No |
| Current-sourcing | Yes |
| Short-circuit protection | Yes |
| Response threshold, typ. | 0.7 to 1.3 A |
| Limitation of inductive shutdown voltage to | Typ. L+ (-50 V) |
| Controlling a digital input | Yes |
| Switching capacity of the outputs |
| on lamp load, max. | 5 W |
| Load resistance range |
| lower limit | 48 Ω |
| upper limit | 12 kΩ |
| Output voltage |
| Type of output voltage | DC |
| for signal "1", min. | Ue minus 1 V |
| Output current |
| for signal "1" rated value | 0.5 A |
| for signal "0" residual current, max. | 0.1 mA |
| Output delay with resistive load |
| "0" to "1", max. | 50 µs |
| "1" to "0", max. | 100 µs |
| Parallel switching of two outputs |
| for uprating | No |
| for redundant control of a load | No |
| Switching frequency |
| with resistive load, max. | 100 Hz |
| with inductive load, max. | 2 Hz |
| on lamp load, max. | 10 Hz |
| Total current of the outputs |
| Current per channel, max. | 0.5 A |
| horizontal installation |
| — up to 60 °C, max. | 2 A |
| — up to 70 °C, max. | 1 A |
| vertical installation |
| — up to 60 °C, max. | 2 A |
| Cable length |
| shielded, max. | 1 000 m |
| unshielded, max. | 600 m |
| Encoder |
| Connectable encoders |
| 2-wire sensor | Yes |
| — permissible quiescent current (2-wire sensor), max. | 1.5 mA |
| Interfaces |
| Number of PROFINET interfaces | 1 |
| Number of PROFIBUS interfaces | 0 |
| PROFIBUS PA |
| Transmission rate, max. | 31.25 kbit/s |
| Number of connectable PA field devices | 8; Electrically isolated from other interfaces, isolation tested at 2 500 V DC |
| Current output to PA field devices, max. | 320 mA |
| permissible current per spur line | 40 mA |
| Automatic addressing | Yes |
| System-supported integration of field devices via PA profiles | Yes |
| Extended fieldbus diagnostics | Yes |
| 1. Interface |
| Interface type | PROFINET |
| Isolated | Yes |
| Interface types |
| Number of ports | 2 |
| integrated switch | Yes |
| BusAdapter (PROFINET) | Yes |
| Protocols |
| PROFINET IO Device | Yes |
| PROFIBUS DP slave | No |
| Interface types |
| RJ 45 (Ethernet) |
| 100 Mbps | Yes |
| Autonegotiation | Yes |
| Autocrossing | Yes |
| Protocols |
| Supports protocol for PROFINET IO | Yes |
| Redundancy mode |
| MRP | Yes |
| PROFINET system redundancy (S2) | Yes; Type S2 |
| Open IE communication |
| LLDP | Yes |
| Isochronous mode |
| Isochronous operation (application synchronized up to terminal) | No |
| Interrupts/diagnostics/status information |
| Status indicator | Yes |
| Alarms | Yes |
| Diagnostics function | Yes |
| Diagnostic messages |
| Monitoring of encoder power supply | Yes |
| Wire-break | Yes |
| Short-circuit | Yes |
| Diagnostics indication LED |
| RUN LED | Yes; Green LED |
| ERROR LED | Yes; Red LED |
| MAINT LED | Yes; yellow LED |
| Monitoring of the supply voltage (PWR-LED) | Yes |
| Digital input status indicator | Yes |
| Digital output status indicator | Yes |
| Spur line status/fault | Yes |
| Potential separation |
| between the channels and PROFINET | Yes |
| Potential separation digital inputs |
| between the channels | No |
| between the channels and the power supply of the electronics | No |
| Potential separation digital outputs |
| between the channels | No |
| between the channels and the power supply of the electronics | No |
| Isolation |
| Isolation tested with | 1 500 V AC between PROFINET and electronics |
| Degree and class of protection |
| Degree of protection acc. to EN 60529 | IP20 |
| Ambient conditions |
| Ambient temperature during operation |
| min. | -40 °C |
| max. | 70 °C |
| horizontal installation, min. | -40 °C |
| horizontal installation, max. | 70 °C; Observe derating |
| vertical installation, min. | -40 °C |
| vertical installation, max. | 60 °C; Observe derating |
| Ambient temperature during storage/transportation |
| min. | -40 °C |
| max. | 85 °C |
| Relative humidity |
| Operation, max. | 95 % |
| Connection method |
| Design of electrical connection | Connection plug |
| Spur line |
| Number of spur lines | 8 |
| Type of cable | Type A |
| Cable diameter, min. | 6 mm |
| Cable diameter, max. | 12 mm |
| Conductor cross-section, min. | 0.2 mm² |
| Conductor cross-section, max. | 2.5 mm² |
| Cable length, max. | 120 m |
| total current output to field devices, max. | 320 mA |
| Number of connectable field devices | 8 |
| Current limitation per field device, max. | 40 mA |
| No-load voltage, max. | 15.3 V |
| short-circuit proof | Yes |
| Short-circuit current (test current); max. | 8 mA |
| intrinsically safe according to FISCO model | Yes |
| Debounce logic | Yes |
| Dimensions |
| Width | 329 mm |
| Height | 123 mm |
| Depth | 74 mm |
| Weights |
| Weight, approx. | 580 g |
| last modified: | 03/08/2019 |
