| SIMATIC DP, POWER M. F-PM-E PPM PROFIsafe, for ET 200SP; 24 V DC safe shutdown of DQ and F-DQ up to PL D/SIL2 or PL E/SIL3 2 for safe dig. inputs 1 for safe dig. output PPM |
| General information |
| Product type designation | F-PM-E 24 V DC/8 A PPM ST |
| usable BaseUnits | BU type C0 |
| Color code for module-specific color identification plate | CC52 |
| Product function |
| I&M data | Yes; I&M0 to I&M3 |
| Engineering with |
| STEP 7 TIA Portal configurable/integrated as of version | V12 |
| STEP 7 configurable/integrated as of version | V5.5 SP3 / - |
| PROFIBUS as of GSD version/GSD revision | V2.3 |
| PROFINET as of GSD version/GSD revision | V2.31 |
| Supply voltage |
| Rated value (DC) | 24 V |
| permissible range, lower limit (DC) | 20.4 V |
| permissible range, upper limit (DC) | 28.8 V |
| Reverse polarity protection | Yes |
| Input current |
| Current consumption (rated value) | 75 mA; without load |
| Current consumption, max. | 21 mA; From the backplane bus |
| Output voltage |
| Rated value (DC) | 24 V |
| Encoder supply |
| Number of outputs | 2 |
| Short-circuit protection | Yes; Electronic (response threshold 0.7 A to 2.1 A) |
| Output current |
| up to 60 °C, max. | 0.3 A |
| 24 V encoder supply |
| 24 V | Yes; min. L+ (-1.5 V) |
| Short-circuit protection | Yes |
| Output current, max. | 600 mA; Total current of all encoders |
| Power |
| Power available from the backplane bus | 70 mW |
| Power loss |
| Power loss, typ. | 5 W |
| Address area |
| Address space per module |
| Inputs | 7 byte |
| Outputs | 5 byte |
| Hardware configuration |
| Automatic encoding | Yes |
| Electronic coding element type F | Yes |
| Digital inputs |
| Number of digital inputs | 2 |
| Source/sink input | Yes; P-reading |
| Input characteristic curve in accordance with IEC 61131, type 1 | Yes |
| Input voltage |
| Type of input voltage | DC |
| Rated value (DC) | 24 V |
| for signal "0" | -30 to +5V |
| for signal "1" | +15 to +30V |
| Input current |
| for signal "1", typ. | 3.7 mA |
| Input delay (for rated value of input voltage) |
| for standard inputs |
| — parameterizable | Yes |
| — at "0" to "1", min. | 0.4 ms |
| — at "0" to "1", max. | 20 ms |
| — at "1" to "0", min. | 0.4 ms |
| — at "1" to "0", max. | 20 ms |
| for technological functions |
| — parameterizable | No |
| Cable length |
| shielded, max. | 1 000 m |
| unshielded, max. | 500 m |
| Digital outputs |
| Number of digital outputs | 1 |
| Short-circuit protection | Yes |
| Response threshold, typ. | > 14.8 A |
| Open-circuit detection | Yes |
| Response threshold, typ. | 8 mA |
| Overload protection | Yes |
| Response threshold, typ. | 8.8 A |
| Limitation of inductive shutdown voltage to | Max. -1.5 V |
| Switching capacity of the outputs |
| with resistive load, max. | 8 A |
| on lamp load, max. | 100 W |
| Load resistance range |
| lower limit | 3 Ω |
| upper limit | 2 000 Ω |
| Output voltage |
| for signal "1", min. | 24 V; L+ (-0.5 V) |
| Output current |
| for signal "1" rated value | 8 A |
| for signal "0" residual current, max. | 1.5 mA; PP-switching: max. 1.5 mA; PM-switching: max. 1 mA |
| Switching frequency |
| with resistive load, max. | 10 Hz; Symmetrical |
| with inductive load, max. | 0.1 Hz; according to IEC 60947-5-1, DC-13, symmetrical |
| on lamp load, max. | 4 Hz; Symmetrical |
| Total current of the outputs |
| Current per channel, max. | 8 A; Note derating data in the manual |
| Current per module, max. | 8 A; Note derating data in the manual |
| Cable length |
| shielded, max. | 1 000 m |
| unshielded, max. | 500 m |
| Interrupts/diagnostics/status information |
| Diagnostics function | Yes, "Alarms/diagnostic messages" section in the manual |
| Substitute values connectable | No |
| Alarms |
| Diagnostic alarm | Yes |
| Hardware interrupt | No |
| Diagnostics indication LED |
| RUN LED | Yes; Green LED |
| ERROR LED | Yes; Red LED |
| Monitoring of the supply voltage (PWR-LED) | Yes; green PWR LED |
| Channel status display | Yes; Green LED |
| for channel diagnostics | Yes; Red LED |
| for module diagnostics | Yes; green/red DIAG LED |
| Potential separation |
| Potential separation channels |
| between the channels | No |
| between the channels and backplane bus | Yes |
| between the channels and the power supply of the electronics | No |
| Isolation |
| Isolation tested with | 707 V DC (type test) |
| Standards, approvals, certificates |
| Highest safety class achievable in safety mode |
| Performance level according to ISO 13849-1 | PLe |
| SIL acc. to IEC 61508 | SIL 3 |
| Ambient conditions |
| Ambient temperature during operation |
| horizontal installation, min. | 0 °C |
| horizontal installation, max. | 60 °C |
| vertical installation, min. | 0 °C |
| vertical installation, max. | 50 °C |
| Dimensions |
| Width | 20 mm |
| Height | 73 mm |
| Depth | 55 mm |
| Weights |
| Weight, approx. | 70 g |
| last modified: | 03/13/2019 |
