| SIMATIC ET 200SP HA, PROFINET interface module IM155-6 PN max. 56 I/O modules, multi-hot swap, without server module |
| General information |
| Product type designation | IM 155-6 PN |
| HW functional status | FS03 |
| Firmware version | V1.1 |
| Vendor identification (VendorID) | 02AH |
| Device identifier (DeviceID) | 030FH |
| Product function |
| I&M data | Yes; I&M0 to I&M3 |
| Engineering with |
| PCS 7 configurable/integrated as of version | V9.0 |
| Configuration control |
| via dataset | No |
| Supply voltage |
| Rated value (DC) | 24 V |
| permissible range, lower limit (DC) | 19.2 V |
| permissible range, upper limit (DC) | 28.8 V |
| Reverse polarity protection | Yes |
| Short-circuit protection | Yes |
| Mains buffering |
| Mains/voltage failure stored energy time | 10 ms |
| Input current |
| Current consumption, max. | 700 mA; +19.2 V to +28.8 V DC |
| Inrush current, max. | 5 A |
| I²t | 0.36 A²·s; Due to increased mains buffering of 10 ms |
| Power |
| Infeed power to the backplane bus | 7.5 W; No doubling in redundant mode as the infeed power is also designed as redundant. |
| Power loss |
| Power loss, typ. | 2.4 W |
| Address area |
| Address space per module |
| Address space per module, max. | 256 byte |
| Address space per station |
| Address space per station, max. | 1 440 byte; 1 440 bytes R1 and S1 without CiR, otherwise 1 000 bytes |
| Hardware configuration |
| Integrated power supply | Yes; 24 V DC |
| Rack |
| Modules per rack, max. | 56; 56 slots for I/O modules + server module (width without IM ≤ 1.3 m) |
| Time stamping |
| Accuracy | 1 ms; In compliance with the supplementary conditions described in the Equipment Manual |
| Interfaces |
| Number of PROFINET interfaces | 1; 2 ports (switch) |
| 1. Interface |
| Interface types |
| Number of ports | 2; via BusAdapter |
| integrated switch | Yes |
| BusAdapter (PROFINET) | Yes; Compatible BusAdapters: BA 2x RJ45, BA 2x FC, BA 2x LC, BA LC/RJ45, BA LC/FC, BA VD |
| Protocols |
| PROFINET IO Device | Yes |
| Open IE communication | Yes |
| Media redundancy | Yes; as MRP client |
| Interface types |
| RJ 45 (Ethernet) |
| Transmission procedure | PROFINET with 100 Mbit/s full duplex (100BASE-TX) |
| 100 Mbps | Yes; PROFINET with 100 Mbit/s full duplex (100BASE-TX) |
| Autonegotiation | Yes |
| Autocrossing | Yes |
| Protocols |
| PROFINET IO Device |
| Services |
| — Open IE communication | Yes |
| Redundancy mode |
| MRP | Yes |
| PROFINET system redundancy (S2) | Yes; S2, R1 |
| Open IE communication |
| TCP/IP | Yes |
| SNMP | Yes |
| LLDP | Yes |
| Interrupts/diagnostics/status information |
| Status indicator | Yes |
| Alarms | Yes |
| Diagnostics function | Yes |
| Diagnostics indication LED |
| RUN LED | Yes; Green LED |
| ERROR LED | Yes; Red LED |
| MAINT LED | Yes; yellow LED |
| ACTIVE-LED (active IM in redundant configuration) | Yes; Green LED |
| Monitoring of the supply voltage (PWR-LED) | Yes; green PWR LED |
| Connection display LINK TX/RX | Yes; 2x green link LEDs on BusAdapter |
| Potential separation |
| between PROFINET and all other circuits | Yes; 1500 V AC |
| between supply and all other circuits | Yes; Type tested with 1 500 V DC |
| Permissible potential difference |
| between different circuits | Safety extra low voltage SELV |
| Isolation |
| Isolation tested with | 1 500 V DC/1 min, type test |
| Ambient conditions |
| Ambient temperature during operation |
| horizontal installation, min. | -40 °C |
| horizontal installation, max. | 70 °C |
| vertical installation, min. | -40 °C |
| vertical installation, max. | 60 °C |
| Dimensions |
| Width | 50 mm |
| Height | 138 mm |
| Depth | 89 mm |
| Weights |
| Weight, approx. | 192 g; without BusAdapter |
| last modified: | 03/12/2019 |
