| SIMATIC ET 200SP HA, Signal relay module changeover contact, RQ 4x120VDC-230VAC/5A CO HA suitable for terminal block K0, color code CC40, module diagnostics |
| General information |
| Product type designation | RQ 4x120 V UC ... 230 V AC/5 A CO HA |
| Firmware version | V1.0 |
| FW update possible | Yes |
| Usable terminal block | TB type K0 |
| Color code for module-specific color identification plate | CC40 |
| Product function |
| I&M data | Yes; I&M0 to I&M3 |
| Engineering with |
| PCS 7 configurable/integrated as of version | V9.0 |
| Redundancy |
| Redundancy capability | No |
| Supply voltage |
| Rated value (DC) | 24 V |
| permissible range, lower limit (DC) | 19.2 V |
| permissible range, upper limit (DC) | 28.8 V |
| Reverse polarity protection | Yes |
| Input current |
| Current consumption (rated value) | 50 mA; At 24 V and energized changeover coils |
| Current consumption, max. | 60 mA; At 19.2 V and energized changeover coils |
| Power loss |
| Power loss, typ. | 2.8 W; At 24 V, energized changeover coils and 5 A current across each changeover contact |
| Address area |
| Address space per module |
| Address space per module, max. | 1 byte; + 1 byte for QI information |
| Digital outputs |
| Number of digital outputs | 4 |
| Switching frequency |
| with resistive load, max. | 2 Hz |
| with inductive load, max. | 0.5 Hz |
| on lamp load, max. | 2 Hz |
| Total current of the outputs |
| Current per channel, max. | 5 A |
| Current per module, max. | 20 A |
| Total current of the outputs (per module) |
| horizontal installation |
| — up to 70 °C, max. | 20 A |
| vertical installation |
| — up to 60 °C, max. | 20 A |
| Relay outputs |
| Number of relay outputs | 4 |
| external protection for relay outputs | yes; 6 A, see data in manual |
| Switching capacity of contacts |
| — with inductive load, max. | 2 A; 2 A (24 V DC), 0.5 A (60 V DC), 0.1 A (120 V DC) |
| — with resistive load, max. | 5 A; 5 A (30 V DC), 5 A (230 V AC) |
| — Switching current, min. | 8 mA |
| — Rated switching voltage (DC) | 24 V; 24 V DC to 120 V DC |
| — Rated switching voltage (AC) | 230 V; 24V AC to 230V AC |
| Cable length |
| shielded, max. | 1 000 m |
| unshielded, max. | 200 m |
| Interrupts/diagnostics/status information |
| Diagnostics function | Yes |
| Substitute values connectable | Yes |
| Alarms |
| Diagnostic alarm | Yes |
| Diagnostic messages |
| Monitoring the supply voltage | Yes |
| — parameterizable | Yes |
| Diagnostics indication LED |
| MAINT LED | Yes; yellow LED |
| Monitoring of the supply voltage (PWR-LED) | Yes; green PWR LED |
| Channel status display | Yes; Green LED |
| for module diagnostics | Yes; green/red DIAG LED |
| Potential separation |
| Potential separation channels |
| between the channels | Yes |
| between the channels and backplane bus | Yes |
| Between the channels and load voltage L+ | Yes |
| Permissible potential difference |
| between different circuits | Between channels: 230 V AC (different system phase) |
| between channels and backplane bus/supply voltage | 230 V AC |
| Isolation |
| tested with |
| between channels and backplane bus/supply voltage | 4 200 V DC/1 min, type test |
| between backplane bus and supply voltage | 1 500 V DC/1 min, type test |
| Between channels | 1 500 V AC/1 min, type test |
| Ambient conditions |
| Ambient temperature during operation |
| horizontal installation, min. | -40 °C; No icing |
| horizontal installation, max. | 70 °C |
| vertical installation, min. | -40 °C; No icing |
| vertical installation, max. | 60 °C |
| Altitude during operation relating to sea level |
| Ambient air temperature-barometric pressure-altitude | 3 000 m due to converter type used |
| Dimensions |
| Width | 22.5 mm |
| Height | 115 mm |
| Depth | 138 mm |
| Weights |
| Weight, approx. | 162 g |
| last modified: | 03/08/2019 |
