| SIPLUS S7-300 SM 326F DI24 40-pole -25...+60°C (70°C with forced convection) with conformal coating based on 6ES7326-1BK02-0AB0 . Digital input F-DI 24x24 V DC Fail-safe digital input for SIMATIC S7 F-systems with diagnostic alarm |
| Supply voltage |
| Rated value (DC) | 24 V |
| Input current |
| from load voltage L+ (without load), max. | 450 mA |
| from backplane bus 5 V DC, max. | 100 mA |
| Encoder supply |
| Number of outputs | 4; Isolated |
| Output current |
| Rated value | 400 mA |
| Power loss |
| Power loss, typ. | 10 W |
| Digital inputs |
| Number of digital inputs | 24 |
| Number of simultaneously controllable inputs |
| all mounting positions |
| — up to 40 °C, max. | 24 |
| — up to 60 °C, max. | 24; (at 24 V) or 18 (at 28.8 V) |
| Input voltage |
| Type of input voltage | DC |
| Rated value (DC) | 24 V |
| for signal "0" | -30 to +5V |
| for signal "1" | +11 to +30V |
| Input current |
| for signal "0", max. (permissible quiescent current) | 2 mA |
| for signal "1", typ. | 10 mA |
| Input delay (for rated value of input voltage) |
| for standard inputs |
| — at "0" to "1", max. | 3.4 ms |
| — at "1" to "0", max. | 3.4 ms |
| Cable length |
| shielded, max. | 200 m |
| unshielded, max. | 100 m |
| Encoder |
| Connectable encoders |
| 2-wire sensor | Yes; if short-circuit test is deactivated |
| — permissible quiescent current (2-wire sensor), max. | 2 mA |
| Interrupts/diagnostics/status information |
| Diagnostics function | Yes |
| Alarms |
| Diagnostic alarm | Yes |
| Diagnostic messages |
| Diagnostic information readable | Yes |
| Diagnostics indication LED |
| Fail-safe operation | Yes |
| Group error SF (red) | Yes |
| Ex(i) characteristics |
| Maximum values of input circuits (per channel) |
| Ta (permissible ambient temperature), max. | 60 °C |
| Potential separation |
| Potential separation digital inputs |
| between the channels | Yes |
| between the channels, in groups of | 12 |
| between the channels and backplane bus | Yes |
| Isolation |
| Isolation tested with | 500 V DC/350 V AC |
| Standards, approvals, certificates |
| CE mark | Yes |
| UL approval | Yes; File E239877 |
| RCM (formerly C-TICK) | Yes |
| KC approval | Yes |
| EAC (formerly Gost-R) | Yes |
| Highest safety class achievable in safety mode |
| acc. to DIN VDE 0801 | AK 6 |
| acc. to EN 954 | Cat. 4 |
| SIL acc. to IEC 61508 | SIL 3 |
| Ambient conditions |
| Ambient temperature during operation |
| min. | -25 °C; = Tmin |
| max. | 60 °C; = Tmax; *+70 °C where forced convection with a minimum air velocity of 0.7 m/s through the modules and rated voltage of 24 V ±5 % are ensured. If in the course of maintenance or automatic diagnosis it is determined that the admissible specified parameters have been exceeded, the modules should be subjected to a proof test (function check) by the manufacturer. |
| Altitude during operation relating to sea level |
| Installation altitude above sea level, max. | 2 000 m |
| Ambient air temperature-barometric pressure-altitude | Tmin ... Tmax at 1 140 hPa ... 795 hPa (-1 000 m ... +2 000 m) |
| Relative humidity |
| With condensation, tested in accordance with IEC 60068-2-38, max. | 100 %; RH incl. condensation/frost (no commissioning under condensation conditions) |
| Resistance |
| Use in stationary industrial systems |
| — to biologically active substances according to EN 60721-3-3 | Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request |
| — to chemically active substances according to EN 60721-3-3 | Yes; Class 3C4 (RH < 75 %) incl. salt spray acc. to EN 60068-2-52 (severity degree 3); * |
| — to mechanically active substances according to EN 60721-3-3 | Yes; Class 3S4 incl. sand, dust, * |
| Use on ships/at sea |
| — to biologically active substances according to EN 60721-3-6 | Yes; Class 6B2 mold and fungal spores (excluding fauna); Class 6B3 on request |
| — to chemically active substances according to EN 60721-3-6 | Yes; Class 6C3 (RH < 75 %) incl. salt spray acc. to EN 60068-2-52 (severity degree 3); * |
| — to mechanically active substances according to EN 60721-3-6 | Yes; Class 6S3 incl. sand, dust; * |
| Remark |
| — Note regarding classification of environmental conditions acc. to EN 60721 | * The supplied plug covers must remain in place over the unused interfaces during operation! |
| Connection method |
| required front connector | 40-pin |
| Dimensions |
| Width | 80 mm |
| Height | 125 mm |
| Depth | 120 mm |
| Weights |
| Weight, approx. | 442 g |
| last modified: | 03/13/2019 |
